M3 'Grease Gun' Submachine Gun
| Country of Origin | United States |
| Type | Submachine Gun |
| Caliber | 11.430 mm |
| Capacity | 30 rounds |
| Length | 756.900 mm |
| Barrel Length | 203.200 mm |
| Weight | 3.700 kg |
| Rate of Fire | 450 rounds/min |
| Range | 91.000 m |
| Muzzle Velocity | 280 m/s |
Contributor: C. Peter Chen
ww2dbaseThe M3 submachine gun was designed by George Hyde in 1942, and they entered American military service on 12 Dec 1942, aiming to replace the Thompson submachine gun. Designed during war time, Hyde focused, and succeeded, in achieving a design that would be simple and cheap to produce. Between 1942 and 1945, 600,000 M3 submachine guns were manufactured.The M3 submachine guns fired in automatic mode only. They were operated by blowback and fired from an open bolt. When American soldiers received the weapons, they nicknamed them "grease guns" as the weapons looked like the common mechanic's tool by the same name.
After the WW2, M3 submachine guns, along with the M3A1 variant designed in 1944, remained in service. They were officially retired in 1957 after an additional 80,000 units were made since 1945, but in actuality they continued to serve long after the official retirement. In the early 1990s, during the Desert Storm conflict, US Army 19th Engineering Battalion troops were equipped with M3A1 submachine guns. They were also used during the Chinese Civil War, Korean War, Vietnam War, and others.
Source: Wikipedia. ww2dbase
Last Major Revision: Jun 2008
M3 'Grease Gun' Submachine Gun Interactive Map
Photographs
 |  |
M3 'Grease Gun' Timeline
| 12 Dec 1942 | M3 submachine gun entered US military service. |
Did you enjoy this article or find this article helpful? If so, please consider supporting us on Patreon. Even $1 per month will go a long way! Thank you. Share this article with your friends: Stay updated with WW2DB: |
Visitor Submitted Comments
2. 
BILLAnonymous says:
27 May 2009 06:41:51 PM
Field striping the Grease Gun was easy just un-screw the barrel, and the bolt and spring come out. To fire the weapon, all you had to do was flip open the small door on the right side, this is were the empty brass flies out you can look and see the 45 ammo in the magazine pull the bolt back with your first finger, a cut-out was designed for this, take the weapon off safty, shoulder the weapon, and fire. Designed to fire on full automatic only. it was a brut designed for close range. I think I've remembered it all,when that .45 slug hits you, your goin down.
After World War II the U.S. exported the weapon to NATO and Allied Nations. Over 655,000 were produced. Some models were made under licence in Argentina, Taiwan and Portugal. Even into the 1990's this weapon could still be found in many armed forces, the U.S. Army still used the weapon into the 1960's.
BILLAnonymous says:27 May 2009 06:41:51 PM
Field striping the Grease Gun was easy just un-screw the barrel, and the bolt and spring come out. To fire the weapon, all you had to do was flip open the small door on the right side, this is were the empty brass flies out you can look and see the 45 ammo in the magazine pull the bolt back with your first finger, a cut-out was designed for this, take the weapon off safty, shoulder the weapon, and fire. Designed to fire on full automatic only. it was a brut designed for close range. I think I've remembered it all,when that .45 slug hits you, your goin down.
After World War II the U.S. exported the weapon to NATO and Allied Nations. Over 655,000 were produced. Some models were made under licence in Argentina, Taiwan and Portugal. Even into the 1990's this weapon could still be found in many armed forces, the U.S. Army still used the weapon into the 1960's.
3. Anonymous says:
17 Feb 2010 11:45:49 AM
I was in the 3RD ACR at Ft Bliss in 1993 and we still had them in the arms room.
17 Feb 2010 11:45:49 AM
I was in the 3RD ACR at Ft Bliss in 1993 and we still had them in the arms room.
4. Annonymous says:
5 May 2010 09:03:34 AM
i'd like to say a big thanks to C. Peter Chen for helping me so much on my history homework. thank you! :)
5 May 2010 09:03:34 AM
i'd like to say a big thanks to C. Peter Chen for helping me so much on my history homework. thank you! :)
5. Anonymous says:
25 Apr 2011 10:05:32 AM
Thanks for all the articles Peter! Really helped me with my WW2 project. Thank you Peter and all WW2 Veterans.
25 Apr 2011 10:05:32 AM
Thanks for all the articles Peter! Really helped me with my WW2 project. Thank you Peter and all WW2 Veterans.
6. Michael says:
29 Jul 2012 02:26:26 PM
-They were in use in (at least) the 73rd Cavalry Rgt (ABN), the only airborne armor unit in the US Army, until they turned in their M-551 Sheridans in 1996.
-BillAnonymous is wrong in one respect. There is no "safety" as such on the M-3. The dust cover had a small tab that would lock the bolt in place when closed but only an idiot would close the dust cover on a cocked gun. See: http://www.shootingillustrated.com/index.php/7343/m3-grease-gun/ for more information.
-I fired the gun and hated it. IF (big if) the magazines worked the rate of fire was terribly slow and the gun was extremely inaccurate.
-There were two clever ideas in the design: 1) the wire stock coulde be removed and used as a wrench to unscrew the barrel locking nut. 2) the stock also has a little tab on it that was used to aid in loading the magazines.
29 Jul 2012 02:26:26 PM
-They were in use in (at least) the 73rd Cavalry Rgt (ABN), the only airborne armor unit in the US Army, until they turned in their M-551 Sheridans in 1996.
-BillAnonymous is wrong in one respect. There is no "safety" as such on the M-3. The dust cover had a small tab that would lock the bolt in place when closed but only an idiot would close the dust cover on a cocked gun. See: http://www.shootingillustrated.com/index.php/7343/m3-grease-gun/ for more information.
-I fired the gun and hated it. IF (big if) the magazines worked the rate of fire was terribly slow and the gun was extremely inaccurate.
-There were two clever ideas in the design: 1) the wire stock coulde be removed and used as a wrench to unscrew the barrel locking nut. 2) the stock also has a little tab on it that was used to aid in loading the magazines.
7. Bill says:
15 Oct 2012 09:53:56 PM
MICHAEL THANKS FOR YOUR COMMENT DATED ON
29 JULY 2012. GLAD TO RECEIVE FEEDBACK
IF I REMEMBER THE M3 GREASE GUN COULD BE FIELD STRIPED DOWN TO SEVEN PARTS. AND YOUR RIGHT THE M3 FEATURED A SPRING-LOADED EJECTOR PORT COVER, THAT ALSO ACTED AS A SAFETY, LOCKING THE BOLT WHEN IT WAS CLOSED.
THE LAST TIME I FIRED THE M3 WAS AT FT.SILL,
OKLAHOMA, IN 1966, AND LATER FIRED IT AGAIN IN 67/68 SERVING W/THE 9TH INFANTRY DIVISION DURING MY FIRST TOUR IN VIETNAM'S MEKONG DELTA.
MY SECOND TOUR 69/70 WAS WITH(IFFV)I FIELD FORCES VIETNAM LOCATED IN THE CENTRAL HIGHLANDS.THE WEAPON WAS STILL IN USE BY THE SOUTH VIETNAMESE ARMY(ARVN)I LIKED THE M3 LATER ON I HAD A CHINESE CHI-COM TYPE 56/AK47
7.62x39mm.
THIS OLD SERGEANT CAN'T REMEMBER EVERYTHING, BUT I DO MY BEST, BUT THAT WAS WHEN I WAS YOUNGER, MUCH YOUNGER...THANKS FOR THE INFO
AND THE MEMORIES MICHAEL.
THE CHINESE CONNECTION:
THE COMMUNIST CHINESE PRODUCED A COPY OF THE
.45 CALIBER M3A1 GREASE GUN, IN LOCAL WORK SHOPS AND MILITARY ARSENALS, AS THE TYPE 36
THE WEAPON WAS ALSO USED BY THE CHINESE NATIONALIST FORCES.
Bill says:15 Oct 2012 09:53:56 PM
MICHAEL THANKS FOR YOUR COMMENT DATED ON
29 JULY 2012. GLAD TO RECEIVE FEEDBACK
IF I REMEMBER THE M3 GREASE GUN COULD BE FIELD STRIPED DOWN TO SEVEN PARTS. AND YOUR RIGHT THE M3 FEATURED A SPRING-LOADED EJECTOR PORT COVER, THAT ALSO ACTED AS A SAFETY, LOCKING THE BOLT WHEN IT WAS CLOSED.
THE LAST TIME I FIRED THE M3 WAS AT FT.SILL,
OKLAHOMA, IN 1966, AND LATER FIRED IT AGAIN IN 67/68 SERVING W/THE 9TH INFANTRY DIVISION DURING MY FIRST TOUR IN VIETNAM'S MEKONG DELTA.
MY SECOND TOUR 69/70 WAS WITH(IFFV)I FIELD FORCES VIETNAM LOCATED IN THE CENTRAL HIGHLANDS.THE WEAPON WAS STILL IN USE BY THE SOUTH VIETNAMESE ARMY(ARVN)I LIKED THE M3 LATER ON I HAD A CHINESE CHI-COM TYPE 56/AK47
7.62x39mm.
THIS OLD SERGEANT CAN'T REMEMBER EVERYTHING, BUT I DO MY BEST, BUT THAT WAS WHEN I WAS YOUNGER, MUCH YOUNGER...THANKS FOR THE INFO
AND THE MEMORIES MICHAEL.
THE CHINESE CONNECTION:
THE COMMUNIST CHINESE PRODUCED A COPY OF THE
.45 CALIBER M3A1 GREASE GUN, IN LOCAL WORK SHOPS AND MILITARY ARSENALS, AS THE TYPE 36
THE WEAPON WAS ALSO USED BY THE CHINESE NATIONALIST FORCES.
8. Buddy says:
1 Mar 2014 10:58:22 AM
I recently purchased a weapon the box says cz25
it looks like a grease gun, but the barrel is less then 4 inches. It has a removable stock, and the gun appears new. It has been cut in three places on the main body before the barrel rendering it unfireable. I don't see any other markings on it. It appears to have a 30 round clip. Can you help me identify this gun, and possibly a complete drawing of the weapon. The rounds seem longer than a 9mm but slimmer. Buddy
1 Mar 2014 10:58:22 AM
I recently purchased a weapon the box says cz25
it looks like a grease gun, but the barrel is less then 4 inches. It has a removable stock, and the gun appears new. It has been cut in three places on the main body before the barrel rendering it unfireable. I don't see any other markings on it. It appears to have a 30 round clip. Can you help me identify this gun, and possibly a complete drawing of the weapon. The rounds seem longer than a 9mm but slimmer. Buddy
9. Alan Chanter says:
5 Aug 2018 06:40:26 AM
The CZ25 mentioned in comment 8 is a post-war submachine gun manufactured by the Ceskoslovensko Zbrojojovka (Czech Arms Company founded in 1919) in Brno. Developed by chief designer Vaclav Holek, the CZ25 and its counterpart the CZ23 were important designs in the development history of the submachine gun since they were the first production weapons to incorporate the ‘over-hung’ or ‘wrap-around‘ bolt. The face of the bolt was deeply recessed, so that when the breech was closed some six inches of the bolt actually surrounded the barrel. This method of construction reduced the overall length of the gun and also kept the centre of balance within a relatively small compass at all times. Due to the short bolt stroke the pistol grip was brought forward to a position where it could also function as the magazine housing. The CZ23 had a wooden stock and the CZ25 a folding metal stock; both were chambered for the 9mm Parabellum cartridge. Some 100,000 were made, and they were widely sold abroad.
Alan Chanter says:5 Aug 2018 06:40:26 AM
The CZ25 mentioned in comment 8 is a post-war submachine gun manufactured by the Ceskoslovensko Zbrojojovka (Czech Arms Company founded in 1919) in Brno. Developed by chief designer Vaclav Holek, the CZ25 and its counterpart the CZ23 were important designs in the development history of the submachine gun since they were the first production weapons to incorporate the ‘over-hung’ or ‘wrap-around‘ bolt. The face of the bolt was deeply recessed, so that when the breech was closed some six inches of the bolt actually surrounded the barrel. This method of construction reduced the overall length of the gun and also kept the centre of balance within a relatively small compass at all times. Due to the short bolt stroke the pistol grip was brought forward to a position where it could also function as the magazine housing. The CZ23 had a wooden stock and the CZ25 a folding metal stock; both were chambered for the 9mm Parabellum cartridge. Some 100,000 were made, and they were widely sold abroad.
10. Wanda says:
4 Oct 2019 09:32:43 AM
What was the original name of M3 nickname the grease gun ?
4 Oct 2019 09:32:43 AM
What was the original name of M3 nickname the grease gun ?
11. Anonymous says:
30 Oct 2024 02:24:50 AM
Some were imported into australia during WW2. The locally made Owen Gun turned out to be a superior weapon for jungle fighting in New Guinea.
30 Oct 2024 02:24:50 AM
Some were imported into australia during WW2. The locally made Owen Gun turned out to be a superior weapon for jungle fighting in New Guinea.
All visitor submitted comments are opinions of those making the submissions and do not reflect views of WW2DB.
Change View
Desktop ViewSearch WW2DB
News
- » Wreck of USS Edsall Found (14 Nov 2024)
- » Autumn 2024 Fundraiser (7 Nov 2024)
- » Nobel Peace Prize for the Atomic Bomb Survivors Organization (11 Oct 2024)
- » Wreck of USS Stewart/DD-224 Found (2 Oct 2024)
- » See all news
Current Site Statistics
- » 1,150 biographies
- » 337 events
- » 43,917 timeline entries
- » 1,241 ships
- » 350 aircraft models
- » 207 vehicle models
- » 375 weapon models
- » 123 historical documents
- » 260 facilities
- » 470 book reviews
- » 28,548 photos
- » 432 maps
Famous WW2 Quote
"Since peace is now beyond hope, we can but fight to the end."Chiang Kaishek, 31 Jul 1937
22 Feb 2009 02:52:09 PM
I was able to fire the M3A1 'GREASE GUN' it had one setting full auto, hell of a kick magazine capacity 20 or 30 rounds of 0.45 caliber ammo designed for short range, and it was heavy, but a very simple weapon to field strip.The rate of fire was 270rpm